How To Repair A Pool Liner

Download Article

Download Commodity

A familiar sight each flavour for many vinyl-liner pool owners is sags or gaps at the rail that holds the liner in place. Constant fluctuations in temperature over the winter can cause the vinyl to stretch and popular out at certain spots—most often at corners or where there is plastic trim in a concrete deck that meets with the puddle coping. In many cases, the vinyl can be pulled up and snapped back into identify in just a few minutes. Dive in!

1. 

   1

   Boil a kettle of water. Information technology may accept several kettles, depending on the size of your liner.^[1]

   • Slowly pour the hot h2o directly on the sagging vinyl below the top edge. Utilize a kettle or tin can with a long spout, such as a watering can.
   • Do non cascade onto the very top edge of the vinyl, but just below the summit, because you next have to grasp that top edge.
   • Pour slowly back and forth beyond the vinyl.

2. 

   2

   Pull the vinyl up. As the hot h2o softens the vinyl, grasp the top edge and firmly pull the vinyl upwardly and above the rail, so that when released it remains just to a higher place the track.^[ii]

   • Information technology may take several cans of water before you tin pull the entire edge upward sufficiently.
   • It may also be necessary to lower the h2o level 6 inches (15.2 cm) or so to increase the amount of vinyl yous can stretch.
   • This task is easier if one person pulls upwardly while the other pours the hot h2o. But i person can do the task lone if necessary.

   Advert

3. 3

   Re-rails the vinyl. Starting on one end, firmly twist the tiptop edge horizontally and push button it into the metallic rail.^[3]

   • The peak underside of the vinyl has a Five shaped groove which should sideslip into a like 5 groove in the top metallic track.
   • You should feel the edge of vinyl skid into the groove, which is supposed to proceed information technology in place.

4. 4

   Agree the vinyl in identify. Employ a large, wooden paint stirrer to help push and hold the vinyl in the track equally you pull the vinyl upwardly and into place.^[iv]

   • Be very careful non to tear through the vinyl.
   • For longer splits use wooden clothes-pegs cleaved in one-half and placed forth the split every few inches.

5. 5

   Finish up. Upon completion of stretching and tucking, get several special short (1/iv to 1/two inch long) plastic jamming pieces from your puddle supply store, and jam them into identify between the top of the plastic and the underside of the metal pool rim. This will help ensure the plastic liner stays in identify.^[5]

Advertizing

1. 1

   Use an extension cord and a pilus dryer or heat gun. ^[6]

   • Heat an area of the liner to stretch by property the accident dryer a couple of inches from the surface and at an bending. Keep the dryer moving and so y'all don't burn the liner. You don't need to superheat the liner—only get it warm enough to make it pliable.

2. ii

   Put the liner back in the runway. Done.^[7]

3. 3

   Notation: Exist careful that no 1 is in the puddle while using electric appliances, as dropping it in the water could be mortiferous.

Advertisement

Add New Question

• Question

  How do I find the leak?

  

  You can use this article to assistance you find the leak: How to Detect a Leak in Your Swimming Pool.

• Question

  My pool ladder is making a pigsty in the liner. What can I do to remedy this?

  

  Motion the ladder out a bit, or maybe try to put a absorber or something in between, to stop it from making holes.

Ask a Question

200 characters left

Include your email address to become a bulletin when this question is answered.

Submit

Advertisement

Video

• Always start in the center of the expanse to exist put dorsum into the track then piece of work to halfway around each side, until the liner is completely dorsum in identify.

• Information technology helps if you can have someone else pour on the boiling water, while you pull the liner into the track.

Thanks for submitting a tip for review!

Advertizing

• Most puddle professionals would non consider using a rut gun or hair dryer to oestrus a liner. Boiling water on the liner is not dangerous if you are conscientious and does non pose any risk to the liner. Any heating element has the ability to create a red-hot ember that could potentially land on the liner and cook a hole in information technology.

• Blow dryer method: electricity and water are non friends - if you lot drop the dryer, exercise not reach for it, unplug the extension string from the wall.

• Remember that y'all are using scalding hot h2o! Be careful where y'all pour it.

Advertizing

About This Article

Article Summary X

Vinyl swimming puddle liners can often sag or sideslip out of position, but luckily y'all have several uncomplicated ways to repair them. Attempt pouring boiling water onto the affected area of vinyl, making certain to leave 1 to 2 inches at the top then y'all can grab hold of information technology. Alternatively, y'all can oestrus an area of the vinyl by blow drying it from near 2 inches abroad. Once the heat from the boiling water or pilus dryer has softened the vinyl, pull information technology up from the meridian to stretch information technology out. Fit it back into the metal trap effectually the top of your pool, which is designed to hold the vinyl in place. If y'all're concerned nigh the vinyl coming loose again, add several plastic jamming pieces, which you tin can buy at a pool supply store. For tips on how to put a patch on your vinyl, read on!

Did this summary help you?

Thanks to all authors for creating a folio that has been read 266,272 times.

Did this article assist you?

Source: https://www.wikihow.com/Repair-a-Swimming-Pool-Vinyl-Liner

Share this post